... what you're trying to do there. You haven't ... />
What you can do is just have a single ... does a RET. Then you do EI and HALT in your main ... program loop. (Note that EI immediately followed by HALT is ... , as the action of EI is actually delayed until the ...

... waiting for down signal
ld a,#0xfe ; signal tx to low ... RESULT_SUCCESS ; report success

ei
ret
[/CODE]
* common types used in code (do not include stdint.h!)
[B]app.c[/B][CODE]int main(int argn,char **argv)

... perfect and you had to do
some experiments with angle ... to connect the signal bus,
- what to do to keep possibility ... , I've plugged this YAMOD int YABUS.ZX.
It is ... screen line as Sam
do.
- YAMOD.KMOUSE - means Kempston ...

... both the TV signal and the composite signal taken from the monitor ... case and what I might do to improve the situation? I ...

... impedance. But it doesn't do that, I think someone has ... why it doesn't actually do anything useful:

... low output impedance where the signal goes into the TV modulator ... tKP_YpyZTC8rrotxlSsZvoIIF4g&hl=es&ei=GwoFTL6JG9LI4gbomtzLDg&sa=X& ...

... to supposedly provide RGB SCART signal - these cables are from ... com/rgbcgatovgac.html[/url]
Signal Requirements:
RGB: 0.7Vpp ... when SCART devices display composite signal, but not when using ... it that some devices can do with less voltage? What is ...

... of the well-documented Z80 do.

First ... is echoed to the INT line. I'm unclear ... READ sets the vertical sync signal as active. IOREQ+WRITE ... So in that case does INT still trigger, with ignoring ... meaning that it usurps INT from the Z80's internal ...

... easy soldering job to do, I connected the cinch ... adhesive foam tape would do the trick. And indeed ... on the spindle, lowering signal-to-noise-ratio.
... // enum tPolicies
const unsigned int cPOLICIES=eFIX_DATA|eACCEPT_ERRORS|eOVERWRITE_OUTPUT; // only ...

... menu, it shows the test signal (colour bars with "1987" in ... - it seems that the test signal should only appear if the ... only get to the test signal colour bars and beeps.
Is there anything I can do, or is my old +2A ...

... />

when trying to do it all in assembly it ...

org 51400
int
push af ; preserve registers ... ; select interrupt mode 2.
ei ; enable interrupts.
#endasm

... PRINT t 19010
PRINT INT (t/69) 275
PRINT ... PRINT t 19010
PRINT INT (t/69) 275
PRINT ... 35.000031 (!)
PRINT t-INT (INT (t/69)*69) 35.000031 ...

... doPrint()
# - Does not do anything with attributes

self.spStorageAddr = int('0x5CB0',16) #Where to store ... - Enable Interupts')
self.doPrint('EI')


#10 - ...

... .

All 3 machines do this.

My suspicion ... the ChinnyVision videos dislikes the signal and keeps cutting out (I ... with resisters but before I do, has anyone come across this ...

... ) and I have a decent signal to the modulator (I get ... have any ideas what to do? 
I only have a ...

... to split the A/V signal and feed it to two ... it's not OK to do this with the RGB signals ...

... Scart to HDMI coverter/upscalers. Do they work OK? Been looking ... ="https://cpc.farnell.com/pro-signal/psg3364/scart-to-hdmi-converter ... "]https://cpc.farnell.com/pro-signal/psg3364/scart-to-hdmi-converter ...

... cycle (called that because the signal /M1 goes low when an ... interrupt acknowledge cycle when the signal /M1 happens to go low ... have a look at the int acknowledge timing diagram, you can ... the Mostek doc). But I do trust the Mostek manual as ...

... the simplest way to do collision detection is ...
struct Sprite {
int x, y; //current position of ... overlaps another. If they do, you have a collision ... is that it may signal a collision even if ... the sprite pixels themselves do not overlap, because the ...

... sp_CreateGenericISR(0xf1f1);
#asm
ei
#endasm

... /* since we couldn't do it in the static initializer ... struct sp_Rect *result);
extern int __LIB__ sp_IntLargeRect(struct sp_LargeRect *r1 ...

... an NMI interrupt or the /INT pin to generate a maskable ... signals on its /NMI and /INT pins depends on the type ... will ignore maskable interrupts. The "ei" instruction re-enables them so ... .LIB's im2_Init() function to do all the im2 set-up ...

... R57 (330R I think) will do nothing....

This ... tracks RFSH, then the signal is getting through and the ... , trigger your scope on ~INT and look at what RFSH ... first display row). Then do the same for 4116 RAS ... me how long after ~INT the ULA RAS go low ...

... be converted to do away with the INT tweak? If ... ]

Syncing with INT is 'only' a tricky-level ... the data bus with an ei/reti combination when (if ... assert WAIT until the INT does occur. Being late ... machine does generate the INT, supply the correct IN ...

... in the first place (normally EI HALT).[/QUOTE]
Yes, I ... (doesn't make much sense do it differently). Phil and I ... if ints are enabled, the int should be taken". If this ...

... too much other stuff to do than refine this routine.

int main(int argc, char **argv)
{
FILE *stream;
int i,j;

if ...

... ULA is still asserting the /INT line during the final tstate ... of an opcode following an EI opcode then the Z80 will ... what does this have to do with Top Gun freezing on ...

... read it.
I do seem to remember you can ... /> ; Read: bit 0 = busy signal from the printer.
; Write ... (SYSVAR_BANK678),a
2216 fb ei

;
... done.
2238 fb ei
2239 37 scf ; ...

... signal that makes a HALT instruction end,
invoke a MASK-INT ... LD B,0 ;redundant
EI ;prepare for returning
RET ... DI ;4 nullify the EI inside MASK-INT
DEC HL ;6 ... ) ;fetch 'FRAMES' for printing
EI
RET

...