-
Rubber key Spectrum mic outputHi, I have the composite modification done on my rubber key Spectrum, I'm thinking about using one of those scart plugs where I can connect the compo…
... stereo jack into the Spectrums mic output or does it have to ... -
shorted MIC output? ToastrackI have this toastrack with no sound output on the MIC. EAR is fine and I can load games perfectly fine. Also I can output sound with no problem on t…
... toastrack with no sound output on the MIC.
EAR is fine ... perfectly fine. Also I can output sound with no problem on ... /> I soldered new EAR and MIC ports but the problem persist ... continuity I found that the MIC is shorted?
I ... -
Audio frequency range from modulator?Anyone know what the frequency range of the audio that's output through the RF? In particular for the 128k/+2. I've checked the manuals but couldn'…
... what the frequency range of the audio that's output through the ... is replicating the RF audio output frequency range. So it sounds authentic ... -
Spectrum mic output lowHi all, Looking for some advice. I’ve got a ZX Spectrum plus and a Sony TCM-939 cassette player. The Sony works great for loading games but, wh…
... the cassette player with the output from my PC and that ... -
Mic output too lowHi all, Looking for some advice. I’ve got a ZX Spectrum plus and a Sony TCM-939 cassette player. The Sony works great for loading games but, wh…
... the cassette player with the output from my PC and that ... -
A few questions about sound and keys in BASICIf I want sound in my BASIC game I have to use BEEP right ? It seems to lock up the CPU for far too long . On Arjun's page I found how to use CALL 94…
... registers the note. If the frequency of the note is low ... bit, worth 8, controls the MIC output and the bit after that ... -
Making sound using the BEEPER in AssemblyI had a look at the the documentation but it doesn't make sense to me. To make music just the beeper all I have to do is send ones and zeros to one o…
... feeding the signal from the MIC socket into the interface itself ... consecutive sounds of the same frequency and loudness on my unmodified ... the same balance on the MIC output (I don’t use the ... -
spectrum48k power supply?Hello, I live in the U.S. and I need to get a power adapter for the spectrum 48k comparable to the original. I needed to know all the specifications…
... all the specifications for output:
like output voltage(i think it ... 's 9v DC), output Amps(I read that it ... center polarity, the watts??, any output frequency and any other important info ... -
ZX Spin 0.3 ReleasedStandard Cut'n'Paste from CSS post again! I can't get to my webpage, so I've uploaded SPIN0.3 to WOS, Alt.Binaries.Comp.Sinclair, and also Daren Pea…
... .
Added CSW/WAV recording (MIC output)
Added TZX/TAP saves ... -
How do I create TAP files from audio tapes ?Hi, How do I create TAP files from ZX Spectrum audio tapes on a Linux box ? I'm new here. Better still, what is a good way to digitally record the …
... digitally record the 48K Spectrum MIC output when doing a SAVE ? and ... -
+2 datacorder noise eliminationHello :-) I have recently bought a gray +2, and as expected, it is plagued with the "datacorder noise in sound output" problem. I have found a few …
... the "datacorder noise in sound output" problem. I have found a ... a relay on the datacorder output, powered from the motor ... line, so that the sound output to the motherboard is disconnected ... suddenly and making the UHF output frequency drift??, etc?? I don' ... -
Disconnecting speaker in TC2048Hello, Does anyone know how speaker in Timex is connected to motherboard? Can it be just unplugged? I would like to disable it somehow (and pass the …
... pass the sound via the mic output to TV set) but I ... -
A clever method of using a single 8-bit register to be used for two things at a timeI don't know if this is the way the SAVE routine in the Spectrum works. Anyway, this is what I've learned today. I've been commented the disassembly…
... is being transferred to the MIC output. It was tought to me ... that is being outputted to MIC, and the counter of bits ... about to be outputted to MIC.
The code is ... byte to be outputted to MIC
SA_BYTE
SCF
+3 sound and mic outputI own a +3 since 198... dunno, it was hard to get it that's all I remember. The thing is it never saved on tape correctly. I read years ago it may be…
I own a +3 since 198... dunno, it was hard to get it that's all I remember. The thing is it never saved on tape correctly. I read years ago it may be a factory fault.
Now I'm trying to get it working again. I found an easy fix for +3 sound:
Realtime Tape Loading, Windows Speccy EmulatorHi folks, I'm very impressed by the amount of Windows Speccy Emulators that have been popping up this year !. What with Spectaculator, ZX SPIN, and…
... released yet), and supports recording MIC output directly to WAV and CSW ...Z80 to TZX Converter !Hey Everyone ! I have a bit of time lately and I coded a little utility that can convert the Z80 snapshot (any version, 48k and 128k supported) to T…
... at 44kHz or whatever your output frequency is.
This means ...New member, dead SpeccyHallo everyone, I was directed here from a Commodore (boo, hiss) forum after pleas of aid with my newly acquired, quite dead 128k Speccy. I sincerely…
... the key clicks on the mic output, and I can tune into ... menu can be discerned. Composite output is dead. We get some ...Poorly Spectrum + Fault diagnosis help needed!Hi, I've got a Spectrum+. Sometime in the past I broke it and sent it off to be fixed. It came back working good as new, but with an issue 2 board i…
... tuned into the Spectrum's output frequency. Even getting a coptright notice ...+2 / 128k via RGB on VGA (TFT)On my (bad layouted - I know) homepage [url]http://www.truppel-online.de/[/url] you can see some photos of RGB picture on VGA - TFT screens. I used a…
... resolutions and has a vertical output frequency of 60 Hz which works ... . 2 has 50 Hz vertical output frequency which does not work with ... a short circuit between RGB output of +2 /128 and Adapter ... resistor in series. This reduces output level to half its value ...+2 datacorder noise eliminationHello :-) I have recently bought a gray +2, and as expected, it is plagued with the "datacorder noise in sound output" problem. I have found a few …
... suddenly and making the UHF output frequency drift??, etc?? I don't ... only know that the sound output to the motherboard is wired ...Why does the speccy make you hear loading?Always wondered this, of all the 8-bit 'puters I have owned, only the Speccy makes you listen to the loading sounds from the tape, why??? I assume it…
... was being recorded on the MIC input (tape deck), causing a ... (Speccy), and back onto the MIC output (speccy).
The result ...Which is the most technically accurate Spectrum Emulator?Ok, which is the most technically accurate Spectrum Emulator? Please don't just vote but give reasons why.
It's just that when you use the MIC output there is also a soft output from the speaker. Cobra's Arc just uses the MIC bit in port #FE to output it's speech synthesis.EAR connector on ZX Spectrum +2 possible?Is it possible to put an EAR connector to the ZX Spectrum +2? I need this because I wish to play the software from the pc as wave file to the spectru…
... />
[quote]
Connecting EAR/MIC in a +2A without making ... used for both EAR and MIC, in the +2 for some ... it only works as the MIC output.
I suppose that ...Spectrum 48 loading problemsHi all, I'm trying to load a program to real 48, but having problems, doesn't work. I was able to write a small Basic program, record it (44kHZ, 8-b…
... I plug both EAR and MIC.
Output works, input nothing. All ...Screen display but with static noisePicked up an sold as seen speccy+ on the bay,the screen on the ebay listing was garbage but i suspect it was due to the seller using his lcd tv so ma…
... , ZX81, Spectrum 16K/48K/+) actually output sound through the TV? The ... signal out, then use the MIC output for audio. You then connect ...Help, How to RGB to VGA Connector on +2A ?Hi, How would I go about converting the RGB output connector from ZX Spectrum +2/A to VGA type of connector. I found this device [url]http://www.am…
... converter inside. It doesn't output VGA, but analog signal. What ... NTSC needs 60 Hz vertical frequency while PAL is based on ... 50 Hz vertical frequency. The converter can handle both ... Hz input vertical frequency into a 60 Hz output frequency. If it would ...Help, How to RGB to VGA Connector on +2A ?Hi, How would I go about converting the RGB output connector from ZX Spectrum +2/A to VGA type of connector. I found this device [url]http://www.am…
... spectrum with PAL and RGB - output to an american TV with ... NTSC needs 60 Hz vertical frequency while PAL is based on ... 50 Hz vertical frequency. The converter can handle both ... Hz input vertical frequency into a 60 Hz output frequency. If it would ...Do you still have the same speccie as when you were young!If so - how old is it now - and is it still working? And does it have rubber keys!?
... a lead to connect the mic output on the back to the ...External Tape / Audio Input on Spectrum +2AEvening all, I've just picked up a Spectrum +2A and have been trying to load TZX files from my Mac into the Spectrum. I know the leads and methods …
... :-)
[U]Connecting a MIC in to a +2A without ... are connected together as a MIC output.
For most solutions ... not to put too high output levels into this port because ... the Spectrums with external tape output, the +2 is always expecting ...save from 48k to PC in wav?I have looked around - in all the wrong places no doubt. I am trying to save a program from my Spectrum 48k to my PC. I am using a standard 3.5mm jac…
... be connected to the Spectrum (MIC output), and the stereo jack to ... , you shoudn't use a MIC input in your sound card ... , but a LINE input. MIC inputs have automatic gain circuitry ...
