(from ZX Computing Aug/Sep'84)



Conversions

-----------



A program with many uses from kitchen to work shop

from Jonathan Court of Poole.

--------------------------------------------------



This program alows the user to convert, for instance, a length

measured in yards, into metres. The 'length' option includes

twelve units of length from millimetres to miles and any one

can be converted to any other, so any length expressed in units

of mm, cm, m, km, inches, feet, yards, fathoms, poles (rods),

chains, furlongs or miles, can be easily converted into the units of

your choice. This section of the program is very useful for

anyone who prefers miles to km, inches to cm, or vice versa.



  The program has 6 sections. As well as length, it allows

conversion between units of area, volume, liquid, capacity, weight

and temperature. All calculations are performed to an accuracy

of 7 significant figures using conversion factors which

have been painstakingly checked.



  The program is menu-driven, and fig.1 shows a screen dump

of the menu. The user enters the number he requires, and one of

six lists results (see fig.2). You are then required to enter the

number of the units that you wish to change.



  Let us suppose that you wish to convert 10 cm into inches. You

enter "2" in reply to the prompt "FROM?", and "5" in reply to

the prompt "TO?". The screen will then appear as shown in

fig.3. You are required to enter the number of cm, 10, in our

case, and this is immediately converted into inches and

displayed to seven significant figures (fig.4). Pressing "L" will

return the user to the list of lengths and the "FROM?"

prompt, and pressing "M" will return you to the menu. This pro-

cedure is the same for the other sections.



  The temperature section only contains three units of

temperature: degrees Centigrade, Fahrenheit and Kelvin.

This is almost the same as before, the answer being given

to two decimal places, since seven-figure accuracy seemed

inappropriate. An example temperature is shown in fig.5.



  Any of the six sections, along with the subroutine at the end of

the program (not necessary for temperature) could be used as a

program on its own, and my routines for giving significant

figures and decimal places, both of which are explained later,

could easily be used in other programs.



  The method I have devised for converting between units is a

simple one, and will not produce answers such as 11.99998

when the answer ought to be 12 or whatever. This is achieved by

using only one complicated conversion factor, the others being

simple powers of ten of the number (for metric units) or simple

whole number multiples or reciprocols for imperial units.

Hence the answers will always be exact and correct to at least

seven significant figures, should this be required.





Program notes

-------------



Line 8            This provides a neat method of clearing a line

                  whenever necessary without having to type

                  in a line of spaces.

Lines 10-120      Here, the menu is printed on the screen.

Lines 130-150     This INPUTs the number, checks it for

                  mistakes, and calls the relevant section of

                  the program.

Line 1000         This is the start of the section dealing with

                  length conversion.

Line 1010         This is the conversion figure used to convert

                  between metric and imperial lengths. It is

                  actually the number of yards in a metre.

Line 1050         An array is set up to hold the twelve units of

                  length.

Line 1060         This array holds the twelve conversion

                  factors. In this array, every unit of length is

                  expressed in terms of yards. This involves

                  numbers, e.g. 1760 for a mile, for imperial

                  lengths, and the conversion factor from line

                  1050 multiplied by a power of ten for metric

                  lengths.

Lines 1070-1300   The arrays are then filled with the

                  appropriate entries.

Lines 1310-1360   The list of lengths is printed on the screen. In

                  line 1350, the part between the brackets

                  prints a space before the number if it is less

                  than ten. This makes for a neater screen

                  layout.

Line 1370         This sets the line on the screen at which the

                  prompts will start

Line 1380         This is the number of lengths. The

                  subroutine being called by line 1390 needs

                  to know this so that it can check for invalid

                  entries.

Line 7000         (This is described here for convenience) This

                  line prints the prompt at the line specified by

                  1370. This position varies according to the

                  length of the list of units in the section.

Lines 7010-7030   The unit to be converted from is entered,

                  checked for invalidity, and displayed next to

                  the word "FROM", over the question mark.

Lines 7040-7070   The unit to be converted to is chosen,

                  checked and displayed.

Lines 7080-7100   The actual length is entered and checked in

                  case it is zero. Entering zero would be

                  pointless unless it was a temperature, and

                  the temperature section does not use this

                  subroutine.

Line 7110         The three (or possibly four) lines just used

                  are cleared using S$ (line 8).

Lines 7120-7130   The original length is displayed along with

                  "IS EQUAL TO">.

Line 7140         This is a very important line. The length (X)

                  is multiplied by the necessary number to give

                  it in terms of its new units. This number is

                  obtained by dividing the value in B (the

                  lengths expressed in yards) of the final units

                  by the value for the original units. The

                  outcome, Y, is the answer. It may be

                  acceptable as it is, but it may be recurring or

                  expressed to a number of decimal places

                  greater than the accuracy of the conversion

                  figures.

Lines 7150-7160   This routine determines the final number of

                  significant figures. The two (6-Z)s give

                  seven significant figures. Any number, x,

                  can be used in place of 6, and the number Y

                  will be reduced (if ncessary) to x+1

                  significant figures.

Lines 7170-7180   Since the ZX81 prints numbers smaller than

                  once as .xyz rather than 0.xyz, I have

                  included these two lines to add a O where

                  necessary to tidy up the answer.

Line 7190         The answer is printed.

Line 7200         We now return to line 1390

Lines 1400-1410   Instructions to proceed are printed at the

                  bottom of the screen.

Line 1420         The program waits until a key is pressed.

Lines 1430        In order to check validity, a variable is

                  assigned. This is probably not necessary, but

                  if the validity checking is more than a couple

                  of lines, it is possible to take one's finger off

                  the appropriate key before the computer has

                  finished.

Lines 1440-1460   The user is returned to the list of lengths or

                  to the menu. 1460 returns to 1410 if an

                  invalid key has been pressed by mistake.

Line 2000         This is the beginning of the section dealing

                  with area conversion.

                  The structure of this section is exactly the

                  same as the length section. The number in

                  line 2010 is the number of square chains in

                  1000 square metres.

Line 3000         This is the beginning of the volume section.

                  This is also the same as the length section,

                  and the number in line 3010 is the number 

                  of cubic inches in 100 cubic centimetres.

Line 4000         This is the liquid capacity section.

                  The number in line 4010 is the number of

                  pints in a litre.

Line 5000         This is the section dealing with weight.

                  The number in line 5010 is the number of

                  pounds in a kilogram. I have used the English

                  spellings of the metric weights rather than

                  the French spellings which seem to have

                  fallen into disuse.

Line 6000         This is the temperature section. It is not the

                  same as the others because simple scalar

                  conversion factors cannot be used since

                  none of the scales share the same zero point.

Lines 6010-6040   The names of the scales are put into the

                  array A$.

Lines 6050-6090   The list is printed on the screen.

Lines 6100-6240   This is similar to the other sections, and

                  allows the user to choose from and to which

                  he is converting, and to input his

                  temperature.

Lines 6250-6260   The temperature is converted into degress

                  Centigrade if it was originally in Kelvin or

                  degrees Fahrenheit.

Lines 6270-6280   The temperature, now in degrees

                  Centigrade, is here converted to the units of

                  your choice if they are not degrees C.

Line 6290         This line reduces the answer to two decimal

                  places. The two 100s will give two decimal

                  places. 1000s would give three, and so on.

Line 6300         The answer is printed by this line.

Lines 6310-6380   This sends the user wherever he now wishes

                  to go, as in previous sections.

Lines 7000-7200   This is the subroutine used in sections one to

                  five and described with section one.

Lines 8000-8010   This SAVEs the program so that it will RUN

                  automatically on loading.

                  The program should be SAVEd by: RUN

                  8000





Spectrum

compatibility

-------------



To the best of my knowledge, this program will run if typed into

any Spectrum. It should be noted that the ** appearing

twice in line 7160 is not two *s, but the ZX81 version of

the   symbol, found on the 'H' key.



