                     Multi-Programming



     Mark Jones with a routine which will enable your

     Spectrum to hold up to 10 Basic programs at once

        - each one directly and easily accessible.



When Clive Sinclair brought out the 1K ZX-81, his first

customers found great limitations in its use. The unexpan-

ded ZX-81 had limited memory, crude graphics and a most

strange display system, which varied in size. Yet a whole

host of impressive software developed for this computer,

pushing it to its limits and further. Sinclair's next

computer, the Spectrum, had a far more impressive specifi-

fication but was still lacking in comparison to, say, the

BBC.

  However, programmers have occasionally manager to produce

excellent games for the Spectrum, showing up even the

games-oriented machines such as the Atari. Admittedly, the

Spectrum will never quite be in the class of these other,

more expensive machines, but at least by using clever

techniques one can push it towards their level. I hope this

routine takes the Spectrum one step nearer.

  This routine is written to allow the Spectrum programmer

the benefit of having up to 10 Basic programs stored in the

computer at one time - a facility normally found only on

more expensive machines. Each program is directly access-

ible by two simple key strokes. Also, jumps to particular

lines in different programs can be made from any Basic

program. For example, you might jump from line 200 of pro-

gram 4 to line 50 of program 6. Thus program 1 might be

used as a menu, calling up games or utilities stored in

programs 2-9.

  When [the program is loaded, you will be] asked how many

programs you want, 1-9. Having selected a number, you will

then step through each program deciding how many bytes to

allocate. A minimum is 200; the maximum number of bytes is

determined by the memory you have free. Once a fixed amount

of memory is allocated to each program, it is not possible

to change this without deleting all the programs.

  Finally you will be asked which program you wish to

initially select. Having selected a program, program A [the

main loading program] will "disappear", leaving you with a

blank Basic program ready for your programming. Program A

can be recalled at any time by selecting program 0.

  If program 0 is selected using keys, it will autostart at

line 4. If you are sure you will not need to reassign

memory to the programs. Incidentally, this has the effect

of NEWing all the programs other than program 0 at one go.

You can NEW program 0. There is little point, though, since

you have nine other program stores at your disposal.

  The multiprogram routine uses the interrupt to check the

keys pressed. To change the program you are currently

handling, simply press Symbol Shift and Break/Space. You

will then be given the following message:

        A=NEW--P=ESCAPE----PROG.? 0-X

where X is the number of programs you are handling.

Pressing P will bring you back to your current program.

Key A will NEW the current program.

  Do not use the Sinclair NEW command, as this may crash

the computer. Otherwise, selecting a number will exchange

your current program with the program selected. All the

program variables, current data read position, and Micro-

drive channels of the old program will be saved. It is

therefore very easy to hop between programs.



 Switching programs



The other way to switch programs is from within a program

itself. Use the following method to do this:

   Routine C   9000 POKE 23619,INT (l/256):

                    POKE 23618,INT (256/l*PEEK 23619)

               9010 POKE 29739,S

               9020 POKE 23729,P

               9030 RANDOMIZE USR 29643

where L = line number to jump to; S = statement number -

normally 0 and P = program.

  Thus for a menu routine which calls three different

programs you might use the following method:

        10 PRINT "Game 1"

        20 PRINT "Game 2"

        30 PRINT "Game 3"

        40 INPUT "Which game (1-3)? ";p

        50 LET s=0: LET l=0

        60 GO TO 9000 (Routine C)

  For those of you who program in machine code it is still

possible to have a RAMtop area free for code. Do this by

altering the variable RTOP in line 22 of program A.

  Different programs occur at different places in memory,

so the first byte of a line 1 REM statement is not neces-

sarily 23760. [Then again, neither is it without this

program, if you have an Interface 1 or similar peripheral,

so wise machine code programmers would take this into

account anyway.]

  When using the printer you will need to turn the inter-

rupt routine off. Do this by typing:

        RANDOMIZE USR 29927

Turn it on again by typing:

        RANDOMIZE USR 29930

You can jump between programs with the interrupt routine

turned off using Routine C.

  The following is a list of subroutines used by the

machine-code routine:



  Address  Function

  29149    Interrupt vector sends interrupt routine here:

           JP to 29475

  29152    Initialisation routine

  29226    Number store routine for above

  29231    Calculates address of system variable storage

           area for each program

  29248    Routine to either retrieve or store necessary

           system variables

  29455    Routine to move machine stack below new program

           RAMtop

  29475    Interrupt routine

           - Reads keyboard + check for Symbol Shift,

           Space/Break

           - Waits for P, A or number

           - Calls different routines depending on what is

           entered

  29630    Delay loop

  29643    Main routine which calls swap routine 29322 and

           checks for errors. If the program number is too

           high an error message will be given.

  29857    Print a string routine

  29883    Print a character routine

  29927    Interrupt routine off

  29930    Interrupt routine on